View SCA100T_7626650.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SCA100T series murata electronic s oy subject to changes 1 / 17 www.muratamems .fi doc.nr. 8261800 rev. b 2 the SCA100T dual axi s inclinometer serie s the SCA100T series is a 3d - mems - based dual axis inclinometer family that provides instrumentation grade perform ance for leveling applications. the measuring axes of the sensing elements are parallel to t he mounting plane and orthogonal to each other. low temperature dependency, high resolution and low noise, together a with robust sensing element design, make the SCA100T the ideal choice f or leveling instruments. the murata inclinometers are u nsensitive t o vibration, due to their over damped sensing elements, and can withstand mechanical shocks of up to 20 000 g . fe atures ? ? ? ? ? ? ? ? ? ? o true self test by deflecting the sensing elements proof mass by electrostatic force. o continuous sensing element interconnection failure check. o continuous memory parity check. ? ? applications ? ? ? ? figure 1. functional block diagram product family specification data sheet self test 2 sensing element 1 sensing element 2 spi interface self test 1 signal conditioning and filtering a/d conversion signal conditioning and filtering eeprom calibration memory 9 st_2 10 st_1 12 vdd 6 gnd 11 out_1 5 out_2 1 sck 3 miso 4 mosi 7 csb temperature sensor
SCA100T series murata electronic s oy subject to changes 2 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 table of contents th e SCA100T dual axis inclinometer series ................................ ................................ ......... 1 features ................................ ................................ ................................ ................................ ............. 1 applications ................................ ................................ ................................ ................................ ...... 1 table of contents ................................ ................................ ................................ ...................... 2 1 electrical specifications ................................ ................................ ................................ ..... 3 1.1 absolute maximum ratings ................................ ................................ ................................ ... 3 1.2 performance characteristics ................................ ................................ ................................ .. 3 1.3 electrical characteristics ................................ ................................ ................................ ....... 4 1.4 spi interface dc characteristics ................................ ................................ ............................ 4 1.5 spi interface ac characteristics ................................ ................................ ............................ 4 1.6 spi interface timing specifications ................................ ................................ ....................... 5 1.7 electrical connection ................................ ................................ ................................ .............. 6 1.8 typical performance characteristics ................................ ................................ .................... 6 1.8.1 additional external compensation ................................ ................................ ...................... 7 2 functional description ................................ ................................ ................................ ....... 9 2.1 measuring directions ................................ ................................ ................................ .............. 9 2.2 voltage to angle conversion ................................ ................................ ................................ . 9 2.3 ratiometric output ................................ ................................ ................................ ................ 10 2.4 spi serial interface ................................ ................................ ................................ ................ 10 2.5 digital output to angle conversion ................................ ................................ ..................... 12 2.6 self test and failure detection modes ................................ ................................ ................ 13 2.7 temperature measurement ................................ ................................ ................................ .. 14 3 application information ................................ ................................ ................................ .... 15 3.1 recommended circuit diagrams and printed circuit board layouts ............................... 15 3.2 recomm ended printed circuit board footprint ................................ ................................ . 16 4 mechanical specifications and reflow soldering ................................ .......................... 16 4.1 mechanical specifications (reference only) ................................ ................................ ....... 16 4.2 reflow soldering ................................ ................................ ................................ ................... 17
SCA100T series murata electronic s oy subject to changes 3 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 1 electrical s pecifications the SCA100T product family comprises two versions, the SCA100T - d01 and the SCA100T - d02 that differ in measurement range. the product version specific performance specifications are listed in the table SCA100T performance characteristics below. all other specifications are common with both versions. vdd=5.00v and ambient temperature unless otherwise specified. 1.1 absolute maximum r atings supply voltage (v dd ) voltage at input / output pins storage t emperature operating temperature mechanical shock esd protection: - human body m odel - charge device model cleaning - 0.3 v to +5.5v - 0.3v to (v dd + 0.3v) - 55c to +125c - 40c to +125c drop from 1 meter onto a concrete surface (20000g) . powered or non - powered 2 kv 500 v ultrasonic cleaning not allowed 1.2 performance c haracteristics parameter condition SCA100T - d01 SCA100T - d02 units measuring range nominal 30 0.5 90 1.0 g frequency response C 3db lp (1 8 - 28 8 - 28 hz offset (out put at 0g) ratiometric output vdd/2 vdd/2 v offset calibration error 0.11 0.23 offset digital output 1024 1024 lsb sensitivity between 01 ( 2 4 70 2 35 v/g mv/ sensitivity calibration error 0.5 0.5 % sensitivity digital output 1638 819 lsb / g offset temperature dependency - 2585c (typical) 0.008 0.008 /c - 40125c (max) 0.86 0.86 sensitivity temperature dependency - 25...85c (typical) 0.014 0.014 %/c - 40125c (max) - 2.5...+1 - 2.5...+1 % typical non - linearity measu ring range 0.11 0.57 digital output resolution between 01 ( 2 11 0.035 11 0.07 bits / lsb output noise density from dc...100hz 0.0008 0.0008 analog output resolution ( 4 bandwidth 10 hz ( 3 0.003 5 0.00 3 5 ratiometric erro r ( 4 vdd = 4.75...5.25v 2 2 % cross - axis sensitivity max. 4 4 % note 1. the frequency response is determined by the sensing elements internal gas damping. note 2. the angle output has sin curve relationship to voltage output note 3. 1 st degree low pas s filtered output resolution = noise density * (bandwidth *1. 6 ) note 4 . typical value for most of the components hz / ?
SCA100T series murata electronic s oy subject to changes 4 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 1.3 electrical c haracteristics parameter condition min. typ max. units supply voltage vdd 4.75 5.0 5.25 v current consumption vdd = 5 v; no load 4 5 ma operating temperature - 40 +125 c analog resistive output load vout to vdd or gnd 10 kohm analog capacitive output load vout to vdd or gnd 20 nf start - up delay reset and parity check 10 ms 1.4 spi interface dc characteristics parameter conditions symbol min typ max unit input ter minal csb pull up current v in = 0 v i pu 13 22 35 ? a input high voltage v ih 4 vdd+0.3 v input low voltage v il - 0.3 1 v hysteresis v hyst 0.23*vdd v input capacitance c in 2 pf input terminal mosi, sck pull down current v in = 5 v i pd 9 17 29 ? a input high voltage v ih 4 vdd+0.3 v input low voltage v il - 0.3 1 v hysteresis v hyst 0.23*vdd v input capacitance c in 2 pf output terminal miso output high voltage i > - 1ma v oh vdd - 0.5 v output low voltage i < 1 ma v ol 0.5 v tristate leakage 0 < v miso < vdd i leak 5 100 pa 1.5 spi interface ac characteristics parameter condition min. typ. max. units output load @500khz 1 nf spi clock frequency 500 khz internal a/d conversion time 150 ? s data transfer time for 8bit command an d 11bit data @500khz 38 ? s
SCA100T series murata electronic s oy subject to changes 5 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 1.6 spi interface timing s pecifications parameter conditions symbol min. typ. max. unit terminal csb, sck time from csb (10%) to sck (90%) t ls1 120 ns time from sck (10%) to csb (90%) t ls2 120 ns terminal sck sck low time load capacitance at miso < 2 nf t cl 1 ? s sck high time load capacitance at miso < 2 nf t ch 1 ? s terminal mosi, sck time from changing mosi (10%, 90%) to sck (90%). data setup time t set 30 ns time from sck (90%) to changing mosi (10%,9 0%). data hold time t hol 30 ns terminal miso, csb time from csb (10%) to stable miso (10%, 90%). load capacitance at miso < 15 pf t val1 10 100 ns time from csb (90%) to high impedance state of miso. load capacitance at miso < 15 pf t lz 10 100 ns terminal miso, sck time from sck (10%) to stable miso (10%, 90%). load capacitance at miso < 15 pf t val2 100 ns terminal csb time between spi cycles, csb at high level (90%) t lh 15 ? s when using spi commands rdax, rday, rwtr: time between convers ion cycles, csb at high level (90%) tlh 150 ? s figure 2. timing diagram for spi communication csb sck mosi miso t ls1 t ch t hol t set t val1 t val2 t lz t ls2 t lh msb in msb out lsb in lsb out data out data in t cl
SCA100T series murata electronic s oy subject to changes 6 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 1.7 electrical connection if the spi interface is not used sck (pin1), miso (pin3), mosi (pin4) and csb (pin7) must be left floating. self - test can be activ ated applying logic 1 (positive supply voltage level) to st_1 or st_2 pins (pins 10 or 9). self - test must not be activated for both channels at the same time. if st feature is not used pins 9 and 10 must be left floating or connected to gnd. inclination signals are provided from pins out_1 and out_2. figure 3. SCA100T electrical connection no. node i/o description 1 sck input serial clock 2 nc input no connect, left floating 3 miso output master in slave out; data out put 4 mosi input master out slave in; data input 5 out_2 output y axis output (ch 2) 6 gnd supply ground 7 csb input chip select (active low) 8 nc input no connect, left floating 9 st_2 input self test input for ch 2 10 st_1 input self test input f or ch 1 11 out_1 output x axis output (ch 1) 12 vdd supply positive supply voltage (+5v dc) 1.8 typical performance c haracteristics typical offset and sensitivity temperature dependencies of the SCA100T are presented in following diagrams. these results represent the typical performance of SCA100T components. the mean value and 3 sigma limits (mean 3 ? standard deviation) and specification limits are presented in following diagrams. the 3 sigma limits represents 99.73% of the SCA100T population. sck miso mosi out_2 gnd vdd out_1 st_1 st_2 csb 1 2 3 4 5 6 7 8 9 10 11 12 sck ext_c_1 miso mosi out_2 vss csb ext_c_2 st_2 st_1/test_in out_1 vdd
SCA100T series murata electronic s oy subject to changes 7 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 figure 4. t ypical temperature dependency of SCA100T offset figure 5. t ypical temperature dependency of SCA100T sensitivity 1.8.1 additional external c ompensation to achieve the best possible accuracy, the temperature measurement information and typical temperature dependency curves can be used for SCA100T offset and sensitivity temperature dependency compensation. the equation of fitted 3 rd order polynome curve for offset compensation is: where: offcorr: 3 rd order polynome fitted to average offset temperature dependency curve t temperature in c (refer to paragraph 2.7 temperature m easurement ) the calculated compensation curve can be used to compensate the temper ature dependency of the SCA100T offset by using following equation: where: offsetcomp temperature compensated offset in degrees offset nominal offset in degrees temperature dependency of SCA100T offset -1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 1 -40 -20 0 20 40 60 80 100 120 temp [c] offset error [degrees] average +3 sigma -3 sigma specification limit specification limit temperature dependency of SCA100T sensitivity -2.50 -2.00 -1.50 -1.00 -0.50 0.00 0.50 1.00 -40 -20 0 20 40 60 80 100 120 temp [c] sensitivity error [%] average +3 sigma -3 sigma specification limit specification limit offcorr offset offsetcomp ? ? 0522 . 0 * 0039 . 0 * 0001 . 0 * 0000006 . 0 2 3 ? ? ? ? ? t t t offcorr
SCA100T series murata electronic s oy subject to changes 8 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 the equation of fitted 2 nd order polynome curve for sensitivity compensation is: wher e: scorr: 2 nd order polynome fitted to average sensitivity temperature dependency curve t temperature in c the calculated compensation curve can be used to compensate the temperature dependency of the SCA100T sensitivity by using following equation: where: senscomp temperature compensated sensitivity sens nominal sensitivity (4v/g SCA100T - d01, 2v/g SCA100T - d02) the typical offset and sensitivity temperature dependency after external compensation is shown in the pictures below. figure 6. the temperature dependency of an externally compensated SCA100T offset figure 7. the temperature dependency of an externally compensated SCA100T sensitivity ) 100 / 1 ( * scorr sens senscomp ? ? 0408 . 0 * 0022 . 0 * 00011 . 0 2 ? ? ? ? t t scorr temperature dependency of externally compensated SCA100T sensitivity -1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 1 -40 -20 0 20 40 60 80 100 120 temp [c] sensitivity error [%] average +3 sigma -3 sigma temperature dependency of externally compensated SCA100T offset -1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 1 -40 -20 0 20 40 60 80 100 120 temp [c] offset error [degrees] average +3 sigma -3 sigma
SCA100T series murata electronic s oy subject to changes 9 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 2 functional description 2.1 measuring d irections x - axis y - axis figure 8. the measuri ng directions of the SCA100T 2.2 voltage to angle c onversion analog output can be transferred to angle using the following equation for conversion: where: offset = output of the device at 0 inclination position, sensitivity is the sensitivity of the device and v dout is the output of the SCA100T. the nominal offset is 2.5 v and the sensitivity is 4 v/g for the SCA100T - d01 and 2 v/g for the SCA100T - d02. angles close to 0 inclination can be estimated quite accurately with straight li ne conversion but for the best possible accuracy, arcsine conversion is recommended to be used. the following table shows the angle measurement error if straight line conversion is used. straight line conversion equation: where: sensitivity = 70mv/ with SCA100T - d01 or sensitivity= 35mv/ with SCA100T - d02 tilt angle [ ] s traight line conversion error [ ] 0 0 1 0.0027 2 0.0058 3 0.0094 4 0.0140 5 0.0198 10 0.0787 15 0.2185 30 1.668 vout > vout =2.5v > vout y sensitivit offset v out ? ? ? ? ? ? ? ? ? ? ? ? ? y sensitivit offset v out arcsin ?
SCA100T series murata electronic s oy subject to changes 10 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 2.3 ratiometric output ratiometric output means that the ze ro offset point and sensitivity of the sensor are proportional to the supply voltage. if the SCA100T supply voltage is fluctuating the SCA100T output will also vary. when the same reference voltage for both the SCA100T sensor and the measuring part (a/d - co nverter) is used, the error caused by reference voltage variation is automatically compensated for. 2.4 spi s erial interface a serial peripheral interface (spi) system consists of one master device and one or more slave devices. the master is defined as a mi cro controller providing the spi clock and the slave as any integrated circuit receiving the spi clock from the master. the asic in murata electronics products always operates as a slave device in master - slave operation mode. the spi has a 4 - wire synchro nous serial interface. data communication is enabled by a low active slave select or chip select wire (csb). data is transmitted by a 3 - wire interface consisting of wires for serial data input (mosi), serial data output (miso) and serial clock (sck). figure 9. typical spi connection the spi interface in murata products is designed to support any micro controller that uses spi bus. communication can be carried out by either a software or hardware based spi. please note that in the ca se of hardware based spi, the received acceleration data is 11 bits. the data transfer uses the following 4 - wire interface: mosi master out slave in p SCA100T miso master in slave out SCA100T p sck serial clock p SCA100T csb chip select ( low active) p SCA100T each transmission starts with a falling edge of csb and ends with the rising edge. during transmission, commands and data are controlled by sck and csb according to the following rules: ? commands and data are shifted; msb first , lsb last ? each output data/status bits are shifted out on the falling edge of sck (miso line) data out (mosi) data in (miso) serial clock (sck) ss0 ss1 ss2 ss3 master microcontroller si so sck cs slave si so sck cs si so sck cs si so sck cs
SCA100T series murata electronic s oy subject to changes 11 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 ? each bit is sampled on the rising edge of sck (mosi line) ? after the device is selected with the falling edge of csb, an 8 - bit command is received. the command de fines the operations to be performed ? the rising edge of csb ends all data transfer and resets internal counter and command register ? if an invalid command is received, no data is shifted into the chip and the miso remains in high impedance state until the f alling edge of csb. this reinitializes the serial communication. ? data transfer to mosi continues immediately after receiving the command in all cases where data is to be written to SCA100Ts internal registers ? data transfer out from miso starts with the fa lling edge of sck immediately after the last bit of the spi command is sampled in on the rising edge of sck ? maximum spi clock frequency is 500khz ? maximum data transfer speed for rdax or rday is 5300 samples per sec for one channel at 500khz clock ? maximum data transfer speed for rdax and rday is 4150 samples per sec for two channel at 500khz clock spi command can be either an individual command or a combination of command and data. in the case of combined command and data, the input data follows uninterrup tedly the spi command and the output data is shifted out parallel with the input data . the spi interface uses an 8 - bit instruction (or command) register. the list of commands is given in table below. command name command format description: meas 000000 00 measure mode (normal operation mode after power on) rwtr 00001000 read temperature data register stx 00001110 activate self test for x - channel sty 00001111 activate self test for y - channel rdax 00010000 read x - channel acceleration rday 00010001 rea d y - channel acceleration measure mode (meas) is standard operation mode after power - up. during normal operation, the meas command is the exit command from self test. read temperature data register (rwtr) reads temperature data register during normal ope ration without affecting the operation. the temperature data register is updated every 150 s. the load operation is disabled whenever the csb signal is low, hence csb must stay high at least 150 s prior to the rwtr command in order to guarantee correct d ata. the data transfer is presented in figure 10 below. the data is transferred msb first. in normal operation, it does not matter what data is written into temperature data register during the rwtr command and hence writing all zeros is recommended. figure 10. command and 8 bit temperature data transmission over the spi
SCA100T series murata electronic s oy subject to changes 12 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 self test for x - channel (stx) activates the self test function for the x - channel (channel 1). the internal charge pump is activated and a high voltage is applied to the x - ch annel acceleration sensor element electrode. this causes the electrostatic force that deflects the beam of the sensing element and simulates the acceleration to the positive direction. the self - test is de - activated by giving the meas command. the self test function must not be activated for both channels at the same time. self test for y - channel (sty) activates the self test function for the y - channel (channel 2). the internal charge pump is activated and a high voltage is applied to the y - channel accelera tion sensor element electrode. read x - channel acceleration (rdax) accesses the ad converted x - channel (channel 1) acceleration signal stored in acceleration data register x. read y - channel acceleration (rday) accesses the ad converted y - channel (channe l 2) acceleration signal stored in acceleration data register y. during normal operation, acceleration data registers are reloaded every 150 s. the load operation is disabled whenever the csb signal is low, hence csb must stay high at least 150 s prior the rdax command in order to guarantee correct data. data output is an 11 - bit digital word that is fed out msb first and lsb last. recommended read cycle for x - ,y - channel and temperature : 1. wait (150 s ) 2. rdax (38 s ) 3. wait (15 s ) 4. rday (38 s ) 5. wait (15 s ) 6. rwtr (32 s ) 7. goto 1. figure 11. command and 11 bit acceleration data transmission over the spi 2.5 digital output to angle c onversion the acceleration measurement results in rdax and rday data registers are in 11 b it digital word format. the data range is from 0 to 2048. the nominal content of rdax and rday data registers in zero angle position are: binary: 100 0000 0000 decimal: 1024 the transfer function from differential digital output to angle can be presented as
SCA100T series murata electronic s oy subject to changes 13 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 where; d out digital output ( rdax or rday) d out@0 digital offset value, nominal value = 1024 ? angle sens sensitivity of the device . (SCA100T - d01: 1638, SCA100T - d02: 819) as an example following table contains data regis ter values and calculated differential digital output values with - 5, - 1 0, 1 and 5 degree tilt angles. angle [] acceleration [mg] rdax (SCA100T - d01) rdax (SCA100T - d02) - 5 - 87.16 dec: 881 bin: 011 0111 0001 dec: 953 bin: 011 1011 1001 - 1 - 17.45 dec: 9 95 bin: 011 1110 0011 dec: 1010 bin: 011 1111 0010 0 0 dec: 1024 bin: 100 0000 0000 dec: 1024 bin: 100 0000 0000 1 17.45 dec: 1053 bin: 100 0001 1101 dec: 1038 bin: 100 0000 1110 5 87.16 dec: 1167 bin: 100 1000 1111 dec: 1095 bin: 100 0100 0111 2.6 self test and failure detection m odes to ensure reliable measurement results the SCA100T has continuous interconnection failure and calibration memory validity detection. a detected failure forces the output signal close to power supply ground or vdd level, out side the normal output range. the calibration memory validity is verified by continuously running parity check for the control register memory content. in the case where a parity error is detected, the control register is automatically re - loaded from the eeprom. if a new parity error is detected after re - loading data both analog output voltages are forced to go close to ground level (<0.25 v) and spi outputs go below 102 counts. the SCA100T also includes a separate self test mode. the true self test sim ulates acceleration, or deceleration, using an electrostatic force. the electrostatic force simulates acceleration that is high enough to deflect the proof mass to the extreme positive position, and this causes the output signal to go to the maximum value. the self test function is activated either by a separate on - off command on the self test input, or through the spi. to ensure that output goes to positive end product must be in 0g position. for position below 0g output change might be limited to +1g chan ge of the output. the self - test generates an electrostatic force, deflecting the sensing elements proof mass, thus checking the complete signal path. the true self test performs following checks: ? sensing element movement check ? asic signal path check ? pcb signal path check ? micro controller a/d and signal path check the created deflection can be seen in both the spi and analogue output.s the self test function is activated digitally by a stx or sty command, and de - activated by a meas command. self test can be also activated applying logic1 (positive supply voltage level) to st pins (pins 9 & 10) of SCA100T. the self test input high voltage level is 4 C vdd+0.3 v and input low voltage level is 0.3 C 1 v. the self test function must not be activated for both channels at the same time . ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? lsb/g lsb lsb arcsin 0 @ sens d d out out ?
SCA100T series murata electronic s oy subject to changes 14 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 figure 12. self test wave forms v1 = initial output voltage before the self test function is activated. v2 = output voltage during the self test function. v3 = output voltage after the self test function has been de - ac tivated and after stabilization time please note that the error band specified for v3 is to guarantee that the output is within 5% of the initial value after the specified stabilization time. after a longer time (max. 1 second) v1=v3. t1 = pulse length for self test activation t2 = saturation delay t3 = recovery time t4 = stabilization time =t2+t3 t5 = rise time during self test. self test characteristics: t1 [ms] t2 [ms] t3 [ms] t4 [ms] t5 [ms] v2: v3: 20 - 100 typ. 25 typ. 30 typ. 55 typ. 15 min 0 .95*vdd (4.75v @vdd=5v) 0.95*v1 - 1.05*v1 2.7 temperature m easurement the SCA100T has an internal temperature sensor, which is used for internal offset compensation. the temperature information is also available for additional external compensation. the tempe rature sensor can be accessed via the spi interface and the temperature reading is an 8 - bit word (0255). the transfer function is expressed with the following formula: where: counts temperature reading t temperature in c the temperature me asurement output is not calibrated. the internal temperature compensation routine uses relative results where absolute accuracy is not needed. if the temperature measurement results are used for additional external compensation then one point calibration i n the system level is needed to remove the offset. with external one point calibration the accuracy of the temperature measurement is about 1 c. vout 5v 0 v t5 t1 t2 t3 t4 v1 v2 v3 st pin voltage 0 v 5 v 083 . 1 197 ? ? ? counts t
SCA100T series murata electronic s oy subject to changes 15 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 3 application information 3.1 recommended circuit d iagram s and printed circuit board l ayouts the SCA100T should be powered from a well regulated 5 v dc power supply. coupling of digital noise to the power supply line should be minimized. 100nf filtering capacitor between vdd pin 12 and gnd plane must be used. if regulator is placed far from component for example oth er pcb it is recommend adding more capacitance between vdd and gnd to ensure current drive capability of the system. for example 470 pf and 1uf capacitor can be used. the SCA100T has a ratiometric output. to get the best performance use the same reference voltage for both the SCA100T and analog/digital converter. use low pass rc filters with 5.11 k and 10nf on the SCA100T outputs to minimize clock noise. locate the 100nf power supply filtering capacitor close to vdd pin 12. use as short a trace length as possible. connect the other end of capacitor directly to the ground plane. connect the gnd pin 6 to underlying ground plane. use as wide ground and power supply planes as possible. avoid narrow power supply or gnd connection strips on pcb. figure 13. a nalog connection and layout example figure 14. spi connection example
SCA100T series murata electronic s oy subject to changes 16 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 3.2 recomme nded printed circuit board f ootprint figure 15. recommended pcb footprint 4 mechanical specifications and reflow s oldering 4.1 mechanical s pecifications ( reference only) lead frame material: copper plating: nickel followed by gold solderability: jedec standard: jesd22 - b102 - c rohs compliance: rohs compliant lead free component. co - planarity error 0.1mm max. the part weights <1.2 g figure 16. mechanica l dimensions of the SCA100T (dimensions in mm)
SCA100T series murata electronic s oy subject to changes 17 / 17 www.muratamems .fi doc. nr. 8261800 rev. b2 4.2 reflow s oldering the SCA100T is suitable for sn - pb eutectic and pb - free soldering process and mounting with normal smd pick - and - place equipment. figure 17. recommended SCA100T body temperature profile during reflow soldering. ref. ipc/jedec j - std - 020b. profile feature sn - pb eutectic assembly pb - free assembly average ramp - up rate (t l to t p ) 3c/second max. 3c/second max. preheat - temperature min (t smin ) - temperature max (t smax ) - time (min to max) (ts) 100c 150 c 60 - 120 seconds 150c 200c 60 - 180 seconds tsmax to t, ramp up rate 3c/second max time maintained above: - temperature (t l ) - time (t l ) 183c 60 - 150 seconds 217c 60 - 150 seconds peak temperature (t p ) 240 +0/ - 5c 250 +0/ - 5c time within 5c of actual peak temperature (t p ) 10 - 30 seconds 20 - 40 seconds ramp - down rate 6c/second max 6c/second max time 25 to peak temperature 6 minutes max 8 minutes max the moisture sensitivity level of the part is 3 according to the ipc/jedec j - std - 020b. the part shoul d be delivered in a dry pack. the manufacturing floor time (out of bag) in the customers end is 168 hours. notes: ? preheating time and temperatures according to guidance from solder paste manufacturer. ? it is important that the part is parallel to the pcb plane and that there is no angular alignment error from intended measuring direction during assembly process. ? wave soldering is not recommended. ? ultrasonic cleaning is not allowed . the sensing element may be damaged by an ultrasonic cleaning proce ss

▲Up To Search▲

Price & Availability of SCA100T

	To Download SCA100T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .